Autumn promotion activity get one machine for free
1. Pneumatic avoidance of the front chuck;
2. Control system, in addition to conventional functions, standard guardrail module, developed specifically for the guardrail industry, easy to use
3. Bus system, bus servo motor,
4. Extreme cost performance;
$16,666.00 Original price was: $16,666.00.$9,999.00Current price is: $9,999.00.
Maximum cutting pipe length | ≤6200 | mm |
Cutting pipe diameter | Round tube 15~160; Square tube, rectangular tube 15~160; Other tubes 15≤Side length≤160; | mm |
Shortest tail | 50 | mm |
X, r axis positioning accuracy | 0.08/1000 | mm |
X, r axis repeat positioning accuracy | ±0.05/1000 | mm |
Acceleration | 0.8 | G |
R axis maximum running speed | 60 | m/min |
Chuck maximum speed | 120 | rpm |
Chuck load weight | 200 | kg |
Main body appearance (length x width x height) | About 8000x2000x2050 (main machine) | mm |
Weight | 1500 | kg |
Laser power | 3000 | w |
Control | JQ | |
Power | 22 | w |
Supply | 380v/50Hz |
Machine display
Bed part
The bed adopts a horizontal structure and a tube-plate welded integrated bed. The whole is annealed to eliminate internal stress. After rough machining, it is subjected to vibration aging and then fine machining, which greatly improves the rigidity and stability of the machine tool and ensures the accuracy of the machine tool.
The AC servo motor drive is controlled by the CNC system. After the motor is driven, the chuck realizes rapid and reciprocating motion in the Y direction, thereby realizing the feeding motion in the Y direction. The Y-axis rack and linear guide rails are both high-precision products, which effectively ensure the accuracy of the transmission; there are limit switches at both ends of the stroke, and hard limit devices are installed at the same time, which effectively ensures the safety of the machine tool movement; the machine tool is equipped with an automatic lubrication device, which adds lubricating oil to the moving parts of the bed at a regular and quantitative time to ensure that the moving parts run in good condition, which can increase the service life of the guide rails, gears, and racks.
Auxiliary support
Two sets of variable diameter wheel support mechanisms are installed on the bed. The variable diameter wheel support is mainly used to assist in controlling the excessive deformation when cutting longer (or smaller diameter) pipes. The system controls the cylinder movement through the solenoid valve to drive the variable diameter wheel up and down, thereby achieving support when cutting pipes; when the rear chuck moves to the corresponding position, the auxiliary support can be lowered to avoid; for pipes of different diameters, the variable diameter wheel can be adjusted to the corresponding diameter scale to achieve a support height suitable for cutting pipes. When the side length of the profile is greater than 110mm, the deformation of the pipe is very small, and the variable diameter wheel support mechanism is no longer enabled.
Chucks
The front chuck is installed at the front end of the bed and is used to clamp the pipe for cutting. Through system control, the front chuck can be driven by the cylinder to move in a small range along the Y-axis direction to avoid the laser head, so that the front and rear chucks can be clamped together to cut the short tail material. The front chuck is designed with a baffle plate and a protective cover to prevent cutting dust from entering the chuck.
The front and rear chucks are driven by AC servo motors to achieve synchronous rotation.
Under the control of the system and the action of the servo motor, the rear chuck can keep the clamping jaws clamped and loosened, and can clamp the pipe and move along the full stroke in the Y direction. The rear chuck is equipped with an independently controlled pressure regulating valve, which can adjust the chuck pressure for pipes of different wall thicknesses.
Gantry part
The gantry adopts a closed structure design of steel pipe welding. After annealing to eliminate internal stress, rough and fine processing are performed to ensure that the components have sufficient rigidity and long-term stability when the laser head moves quickly, thereby ensuring the cutting accuracy.
Loading (Optional)
The machine can be equipped with an optional loading and unloading device. ,so as to reduce labor intensity during work.
We will contact you within 1 working day, please pay attention to the email with the suffix “@jqlaser.com”.
We will contact you within 1 working day, please pay attention to the email with the suffix “@jqlaser.com”.
We will contact you within 1 working day, please pay attention to the email with the suffix “@jqlaser.com”.